Niagara 3000 Delivers Power, Protection, Performance
Power management is a hot topic in audio. Niagara 3000 loves the attention.
Loading...
Amplifier-End Connector: Multi-Spade, Banana, U-Spade, or V-Spade
Often, the choice between terminating your speaker cables with spade lugs or banana plugs will come down to personal preference. However, the EU-compliant isolated binding posts used on some power amplifiers often makes it difficult if not impossible to tighten spade lugs with high torque or pressure. In these applications, the AudioQuest banana connector is the superior choice, and may be the only choice.
AudioQuest has conducted a fairly extensive survey of contemporary amplifier manufacturers to determine whether spades or bananas will be most appropriate for a given brand and model of amplifier. Please contact us, provide the brand and model of the amplifier, and we’ll respond with the optimal connector type.
Given the girth and weight of our Mythical Creature Series speaker cables, a spade may be better capable of fully supporting the cable. This is particularly a concern with binding posts that do not allow a banana connector to fully seat into the post. The EU-compliant posts will neither accept our V-Spade nor allow our Multi-Spade to be fully seated. For these applications (or when you’re not certain), we highly recommend the U-Spade, as it can accommodate any binding post. The V-Spade is a specialty spade connector that works well with large wingnut binding posts (such as the Mundorf ), as it allows extra clearance.
Speaker-End Connector: Spade or Banana
Here we typically recommend the U-Spade or banana connector. However, even though there is less weight and pressure on this side of the cable (particularly for BiWire sets), it is nevertheless important to note the binding post’s design. If a banana connector cannot seat all the way into the binding post, we recommend one of our spade connectors.
Specifications
Specifications
Description
Description
- Low-Z Power Noise-Dissipation
- Polished High-Tension Surfaces with Hanging- Silver Plating
- Significantly Greater Metal Mass For Optimum Current Delivery
- Beryllium-Copper Base Metal
- Includes Duplex Outlet, Wall Plate and Hardware
Polished High-Tension Surfaces with Hanging-Silver Plating
Ensures the lowest distortion of any plated or clad material. It also efficiently transfers signal-masking radio frequency noise toward your utilities transformer and earth ground, far away from your sensitive components.
Significantly Greater Metal Mass for Optimum Current Delivery
No other AC outlet boasts such low impedance for optimum current delivery. This is not only limited to the receptacles' retention blades, but includes the critical ground, wire, and spade-lug connections.
Beryllium-Copper Base Metal
This metal provides superior gripping strength and long-lasting, low-impedance AC power connections. Typical materials such as brass, and high-purity copper aided by spring and wedge devices cannot equal the unparalleled retention strength of high-mass beryllium-copper.
Ensures the lowest distortion of any plated or clad material. It also efficiently transfers signal-masking radio frequency noise toward your utilities transformer and earth ground, far away from your sensitive components.
Significantly Greater Metal Mass for Optimum Current Delivery
No other AC outlet boasts such low impedance for optimum current delivery. This is not only limited to the receptacles' retention blades, but includes the critical ground, wire, and spade-lug connections.
Beryllium-Copper Base Metal
This metal provides superior gripping strength and long-lasting, low-impedance AC power connections. Typical materials such as brass, and high-purity copper aided by spring and wedge devices cannot equal the unparalleled retention strength of high-mass beryllium-copper.
This AC outlet is intended for single phase AC branch circuits ranging from 220 to 240 volts AC, with either a 50 or 60 Hertz sine wave frequency. If the branch circuit uses a 15 amp circuit breaker, it is appropriate to employ the NRG Edison 15. For a 20 amp service, use an NRG Edison 20. The service circuit breaker should be 20 amp rated with at least #12 AWG wiring or heavier (lower number) gauge.
Recommendations for dedicated wiring:
The AudioQuest NRG Edison 15 & 20 AC duplex outlet can accommodate up to #8 AWG wiring, although #10 or #12 may have superior properties versus #8 AWG wire in terms of noise dissipation, that is, routing RF noise back to the electrical panel and ground rod-stake. This is due to skin effect at radio frequencies favoring thinner wire gauges, thus making noise reduction more efficient with a thinner wire gauge. This is an important consideration when optimizing your system with a dedicated line, that is, a discrete Line, Neutral, and Ground wire that travels back to your primary electrical panel without other AC outlets being daisy-chained or series connected to or from any of these wire leads.
The lower the wire resistance (using heavier wire-cable), the lower the AC impedance that is present at 50-60 Hz. This is an advantage for any power amplifier. However, it is equally true that providing optimal noise dissipation (routing radio frequency noise away from your system’s delicate components), is more efficient with slightly smaller wire diameters. Whenever possible, solid core electrical grade AC wiring will yield superior results. We find that when a dedicated AC line is installed, #10 to #12 AWG wiring is the best compromise regardless of whether the branch circuit is meant for 15 or 20 amp operation.
A dedicated line may not be possible (nor is it absolutely necessary), particularly if the installation is in a rented, leased, or temporary space. Even with stock wiring of a 10 or 15 amp service, your system will benefit greatly from the installation of the NRG Edison AC duplex outlet.
Downloads
Downloads
| Technical Specifications | |
|---|---|
Amperage |
|
Voltage |
|
| Weights & Dimensions | |
Sold As |
|
NRG Edison AC Outlet
(Click hotspots for details)
 NRG Edison$199.95 View details | |
|---|---|
Amperage |
|
Voltage |
|
Sold As |
|
News & Reviews
-
-
PowerQuest Delivers
Alberto Pittaluga dives deep into the benefits of power conditioning, explores the relatively modest PowerQuest 3, and decides it’s staying in his system.
-
On a Power Quest
Phil Wright goes on a power quest and arrives at Niagara.
-
Zen Widow Delivers Sonic Thrills
Originally published in the April issue of The Absolute Sound, Derk Richardson's excellent review of Zen Widow's latest release, IV: (from one dark age to another), is now available online.
-
Icons of Audio: Bill Low
AudioQuest’s founder and chief designer, William E. Low, is the featured guest in the premier episode of Stereophile’s YouTube series, “Icons of Audio.”
-
Niagara 1200 Saves the Day
Artur Evers of Like HiFi puts Niagara 1200 through its paces and, indeed, he likes.
-
Why HDMI Cables Are Important
In this video, Walts TV hosts a discussion with Angelo, a Field Educator responsible for product training at AudioQuest. We delve into viewer comments from previous AudioQuest videos, exploring the intricacies of...
-
20 AudioQuest Products Named TAS Editors' Choice
We are delighted to announce that 20 AQ products — across a wide range of categories, all representing outstanding performance and value — have received TAS’s 2024 Editors’ Choice Award.
